Cixi Ningbo | +86 15857443259 | sales@nbchic.com
| Inquiry
Instant Quote

Contact Us

WeChat / 微信

+86 15857443259

Add us on WeChat by this number, or email us and we will send our QR code.

Email Us

sales@nbchic.com

Tap to copy, or write to us any time — we reply within 24 hours.

Open Email App
20 models · 10–190 kW

Direct Fired Diesel Heater 20 Models from 10 to 190 kW

A direct fired diesel heater is the simplest way to turn fuel into hot air: the burner fires into an open chamber and a fan pushes the heated air — combustion gases included — straight into the space. 20 of our 28 diesel and kerosene models are built this way, from 10 kW to 190 kW, or 34,121 to 648,307 BTU/h, across 10 output steps.

The range runs from the FS10-21A at 10 kW — small workshops, garages, market stalls and single-room site huts — up to the FS190-20C at 190 kW, which is 648,307 BTU/h, for the largest industrial halls and major project heating. In between, 7 models reference industrial or factory use in their specification sheets, 5 reference warehouse, loading-bay, storage or distribution work, 6 reference construction and renovation work, and 3 reference agricultural buildings, barns or livestock sheds.

All 20 share the category build: 441-grade stainless steel combustion chamber rated to 1000°C, overheat cut-off, heat-dissipation protection, flameout protection, shutdown protection and an error indicator light, with the electrical load limited to the fan motor, ignition and fuel pump. Because the flue gases go into the heated air, direct fired units are specified for ventilated spaces rather than sealed occupied rooms. Every model on this page is built for diesel or kerosene only — no model here is approved for petrol or bio-oil.

Request a Quote See All 20 Models

190kW Diesel Forced Air Heater for Extreme Cold FS190-20C
Key Figures

The Direct Fired Range at a Glance

Direct fired means the flame heats the air stream itself and a fan delivers it, so the combustion gases enter the heated air. BTU/h is converted from the published kW rating at 1 kW = 3,412.14 BTU/h.

20direct fired models in the range
10output steps from 10 to 190 kW
34,121–648,307BTU/h equivalent, low to high
2of them with thermostat control
Model Range

All 20 Direct Fired Diesel and Kerosene Heaters

Click a model to open its full specification sheet, feature list and recommended applications.

10kW Diesel Forced Air Heater for Small Workshops FS10-21AFS10-21A10kW Diesel Forced Air Heater for Small Workshops FS10-21A10 kW · 34,121 BTU/h · Direct firedPortable 10kW Diesel Heater for Intermittent Use FS10-23AFS10-23APortable 10kW Diesel Heater for Intermittent Use FS10-23A10 kW · 34,121 BTU/h · Direct fired20kW Diesel Forced Air Heater with Thermostat FS20-23AFS20-23A20kW Diesel Forced Air Heater with Thermostat FS20-23A20 kW · 68,243 BTU/h · Direct fired20kW Direct Fired Diesel Heater for Drying and Plaster Work FS20-21AFS20-21A20kW Direct Fired Diesel Heater for Drying and Plaster Work FS20-21A20 kW · 68,243 BTU/h · Direct fired20kW Diesel Space Heater for Agricultural Buildings FS20-19AFS20-19A20kW Diesel Space Heater for Agricultural Buildings FS20-19A20 kW · 68,243 BTU/h · Direct fired20kW Diesel Heater for Marquees and Temporary Structures FS20-21BFS20-21B20kW Diesel Heater for Marquees and Temporary Structures FS20-21B20 kW · 68,243 BTU/h · Direct fired30kW Diesel Forced Air Heater for Workshop Floors FS30-19AFS30-19A30kW Diesel Forced Air Heater for Workshop Floors FS30-19A30 kW · 102,364 BTU/h · Direct fired30kW Diesel Heater for Open Fronted Work Areas FS30-19BFS30-19B30kW Diesel Heater for Open Fronted Work Areas FS30-19B30 kW · 102,364 BTU/h · Direct fired30kW Diesel Heater for Renovation and Building Work FS30-23BFS30-23B30kW Diesel Heater for Renovation and Building Work FS30-23B30 kW · 102,364 BTU/h · Direct fired50kW Diesel Forced Air Heater for Industrial Spaces FS50-19AFS50-19A50kW Diesel Forced Air Heater for Industrial Spaces FS50-19A50 kW · 170,607 BTU/h · Direct fired50kW Diesel Heater with High Capacity Fan for Warehouses FS50-19BFS50-19B50kW Diesel Heater with High Capacity Fan for Warehouses FS50-19B50 kW · 170,607 BTU/h · Direct fired50kW Diesel Heater for Dock Yards and Rail Works FS50-23BFS50-23B50kW Diesel Heater for Dock Yards and Rail Works FS50-23B50 kW · 170,607 BTU/h · Direct fired60kW Diesel Forced Air Heater for High Ceiling Halls FS60-19AFS60-19A60kW Diesel Forced Air Heater for High Ceiling Halls FS60-19A60 kW · 204,728 BTU/h · Direct fired60kW Diesel Heater for Barns and Agricultural Buildings FS60-19BFS60-19B60kW Diesel Heater for Barns and Agricultural Buildings FS60-19B60 kW · 204,728 BTU/h · Direct fired60kW Diesel Heater with Thermostat for Event Halls FS60-23BFS60-23B60kW Diesel Heater with Thermostat for Event Halls FS60-23B60 kW · 204,728 BTU/h · Direct fired80kW Diesel Forced Air Heater for Large Industrial Buildings FS80-20CFS80-20C80kW Diesel Forced Air Heater for Large Industrial Buildings FS80-20C80 kW · 272,971 BTU/h · Direct fired100kW Diesel Forced Air Heater for Factories and Sites FS100-20CFS100-20C100kW Diesel Forced Air Heater for Factories and Sites FS100-20C100 kW · 341,214 BTU/h · Direct fired115kW Diesel Heater for Heavy Industry Buildings FS115-20CFS115-20C115kW Diesel Heater for Heavy Industry Buildings FS115-20C115 kW · 392,396 BTU/h · Direct fired150kW Diesel Heater for Large Halls and Remote Sites FS150-20CFS150-20C150kW Diesel Heater for Large Halls and Remote Sites FS150-20C150 kW · 511,821 BTU/h · Direct fired190kW Diesel Forced Air Heater for Extreme Cold FS190-20CFS190-20C190kW Diesel Forced Air Heater for Extreme Cold FS190-20C190 kW · 648,307 BTU/h · Direct fired
Specification Table

Direct Fired Diesel Heaters — Full Specification

Heat output as published on each model’s own specification sheet. The BTU/h column is the kilowatt figure converted at 1 kW = 3,412.14 BTU/h — it is a conversion, not a second rating.

Direct fired diesel and kerosene heater range — specification
ModelHeat outputEquivalentFiringRecommended use
FS10-21A10 kW34,121 BTU/hDirect firedSmall workshops, garages, market stalls and single-room site huts
FS10-23A10 kW34,121 BTU/hDirect firedService vans, small greenhouses, mobile workshops
FS20-23A20 kW68,243 BTU/hDirect firedSmall construction sites, workshops, garages
FS20-21A20 kW68,243 BTU/hDirect firedRetail units, showrooms, drying rooms
FS20-19A20 kW68,243 BTU/hDirect firedAgricultural buildings, poultry and livestock sheds, barns
FS20-21B20 kW68,243 BTU/hDirect firedEvent marquees, temporary site accommodation, outdoor working areas
FS30-19A30 kW102,364 BTU/hDirect firedMedium workshops, warehouses, factory aisles
FS30-19B30 kW102,364 BTU/hDirect firedLoading bays, cold-storage depots, distribution centres
FS30-23B30 kW102,364 BTU/hDirect firedRenovation and drying projects, dehumidification support
FS50-19A50 kW170,607 BTU/hDirect firedLarge workshops, factory floors, hangars
FS50-19B50 kW170,607 BTU/hDirect firedWarehouse aisles, logistics hubs, storage halls
FS50-23B50 kW170,607 BTU/hDirect firedDock yards, rail and road works, outdoor assembly areas
FS60-19A60 kW204,728 BTU/hDirect firedLarge industrial halls, production workshops
FS60-19B60 kW204,728 BTU/hDirect firedAgricultural sheds, barns, large livestock buildings
FS60-23B60 kW204,728 BTU/hDirect firedExhibition halls, event venues, temporary large structures
FS80-20C80 kW272,971 BTU/hDirect firedLarge warehouses, aircraft and equipment hangars
FS100-20C100 kW341,214 BTU/hDirect firedFactory units, large construction sites, temporary site offices
FS115-20C115 kW392,396 BTU/hDirect firedHeavy industry, shipyards, steel and fabrication shops
FS150-20C150 kW511,821 BTU/hDirect firedVery large halls, mining camps, remote project sites
FS190-20C190 kW648,307 BTU/hDirect firedLargest industrial halls, major project and event heating
Output Steps

Output Steps on This Page

10 output steps across these 20 models, from 10 kW to 190 kW. The largest is the FS190-20C at 190 kW.

Direct fired diesel and kerosene heater range — output steps
Output stepEquivalentModelsModel codes
10 kW34,121 BTU/h2FS10-21A, FS10-23A
20 kW68,243 BTU/h4FS20-23A, FS20-21A, FS20-19A, FS20-21B
30 kW102,364 BTU/h3FS30-19A, FS30-19B, FS30-23B
50 kW170,607 BTU/h3FS50-19A, FS50-19B, FS50-23B
60 kW204,728 BTU/h3FS60-19A, FS60-19B, FS60-23B
80 kW272,971 BTU/h1FS80-20C
100 kW341,214 BTU/h1FS100-20C
115 kW392,396 BTU/h1FS115-20C
150 kW511,821 BTU/h1FS150-20C
190 kW648,307 BTU/h1FS190-20C
Where They Sell

What a Direct Fired Diesel Heater Is Specified For

Direct fired is bought for volume and for speed of warm-up, in spaces that are ventilated.

Workshops, factory floors and hangars

6 of the 20 reference workshop use and 7 reference industrial or factory use; the top of the range reaches 190 kW for hangars and the largest industrial halls.

Warehouses, loading bays and distribution centres

5 models reference warehouse aisles, loading bays, cold-storage depots or distribution centres — the volumes a direct fired unit heats fastest.

Construction, renovation and agricultural buildings

6 reference construction sites, renovation and drying work; 3 reference agricultural buildings, barns and livestock sheds.

FAQ

Direct Fired Diesel Heaters — Common Questions

What does direct fired actually mean?

The flame fires into an open chamber and the fan delivers the heated air — combustion gases included — straight into the space. There is no heat exchanger and no flue, which is why a direct fired unit warms a cold building faster than an indirect unit of the same rating.

How many direct fired models do you make?

20 of the 28 in this category, from 10 kW to 190 kW — 34,121 to 648,307 BTU/h — across 10 output steps.

Is direct fired safe indoors?

It is safe in ventilated spaces: workshops, loading bays, site huts and barns with air movement. It is not the right choice for a sealed room full of people, or for dust-sensitive, coating or food areas — there the flue has to be ducted away. See the indirect fired diesel heater page.

Can I have a thermostat on a direct fired unit?

2 of the 20 carry thermostat control: the FS20-23A, FS60-23B. See the kerosene heater with thermostat page.

What is the largest direct fired heater you build?

The FS190-20C at 190 kW, which is 648,307 BTU/h. The smallest is the FS10-21A at 10 kW.

Will it run on kerosene instead of diesel?

Yes — diesel or kerosene only, on all 20 models. Petrol and bio-oil are excluded on every specification sheet in this category.

Need Direct Fired Diesel Heater Pricing?

Send the model, the specification you want, your market and the target quantity — we reply within 24 hours with FOB pricing, lead time and a loading plan.

Send Inquiry